{"product_id":"uzin-pe-400-vochtscherm-12-kg","title":"UZIN PE 400 Moisture Barrier 12 kg","description":"\u003cp class=\"PDq2pG_selectionAnchorContainer\"\u003eUZIN PE 400 is a ready-to-use, solvent-free dispersion moisture barrier for isolating residual moisture in cement-based floors. The product is applied before the floor is smoothed and is suitable for cement and sand-cement screeds above ground level.\u003cspan class=\"PDq2pG_selectionAnchor\"\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003eWhen used as a moisture barrier, UZIN PE 400 is applied in two coats. The first coat is diluted 1:1 with water and ensures good anchoring in the substrate. The second coat is applied undiluted and forms the moisture-insulating film.\u003c\/p\u003e\n\u003cp\u003eUnder good conditions, both coats can be smoothed approximately three hours after application begins.\u003c\/p\u003e\n\u003ch3\u003eKey properties\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eReady to use\u003c\/li\u003e\n\u003cli\u003eSolvent-free\u003c\/li\u003e\n\u003cli\u003eVery fast-drying\u003c\/li\u003e\n\u003cli\u003eFilm-forming\u003c\/li\u003e\n\u003cli\u003eAlkali-resistant\u003c\/li\u003e\n\u003cli\u003eHigh vapor impermeability\u003c\/li\u003e\n\u003cli\u003eEasy to apply with a roller\u003c\/li\u003e\n\u003cli\u003eMaximum residual moisture content of 4 CM-% on suitable sand-cement screeds\u003c\/li\u003e\n\u003cli\u003eFirst coat diluted, second coat undiluted\u003c\/li\u003e\n\u003cli\u003eCan be smoothed after approximately three hours\u003c\/li\u003e\n\u003cli\u003eFor cement-based floors above ground level\u003c\/li\u003e\n\u003cli\u003eSuitable for indoor use\u003c\/li\u003e\n\u003cli\u003eVery low emissions according to EMICODE EC 1 PLUS\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSuitable as a moisture barrier\u003c\/h3\u003e\n\u003cp\u003eUZIN PE 400 can be applied as a two-coat moisture barrier on:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCement-based screeds\u003c\/li\u003e\n\u003cli\u003eSand-cement screeds\u003c\/li\u003e\n\u003cli\u003eMoisture-insensitive cement-based substrates\u003c\/li\u003e\n\u003cli\u003eNew cement screeds with an elevated residual moisture content\u003c\/li\u003e\n\u003cli\u003eSuitable floors above ground level\u003c\/li\u003e\n\u003cli\u003eSand-cement screeds with a maximum residual moisture content of 4 CM-%\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eAfter smoothing, suitable as a floor build-up beneath, among others:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCarpet\u003c\/li\u003e\n\u003cli\u003eCork\u003c\/li\u003e\n\u003cli\u003eLinoleum\u003c\/li\u003e\n\u003cli\u003eUnderfloor-heated floor coverings\u003c\/li\u003e\n\u003cli\u003ePVC floor coverings\u003c\/li\u003e\n\u003cli\u003eLVT and PVC design flooring\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe floor covering is not bonded directly to UZIN PE 400. After it has fully dried, a suitable smoothing layer must always be applied first.\u003c\/p\u003e\n\u003ch3\u003eAlso suitable as a bonding primer\u003c\/h3\u003e\n\u003cp\u003eUZIN PE 400 can also be used as a bonding primer on cement-based renovation floors with firmly adhering, water-resistant adhesive residues.\u003c\/p\u003e\n\u003cp\u003eFor water-resistant adhesive residues on a calcium sulfate or anhydrite floor, a suitable primer must be used, such as UZIN PE 360 PLUS or UZIN PE 375. Do not use UZIN PE 400 here as a moisture barrier.\u003c\/p\u003e\n\u003ch3\u003eNot suitable for\u003c\/h3\u003e\n\u003cp\u003eUZIN PE 400 is not intended for:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eFloors below ground level\u003c\/li\u003e\n\u003cli\u003eBasements\u003c\/li\u003e\n\u003cli\u003eRising damp\u003c\/li\u003e\n\u003cli\u003eFloors with standing water\u003c\/li\u003e\n\u003cli\u003eCalcium sulfate or anhydrite screeds with elevated residual moisture\u003c\/li\u003e\n\u003cli\u003eUse as a moisture barrier under parquet or wooden floors\u003c\/li\u003e\n\u003cli\u003eUse as a moisture barrier under rubber floor coverings\u003c\/li\u003e\n\u003cli\u003eDirect bonding of floor coverings\u003c\/li\u003e\n\u003cli\u003eOutdoor areas\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eWith higher moisture content, rising damp, or use below ground level, a suitable epoxy or PU moisture barrier is required.\u003c\/p\u003e\n\u003ch3\u003eApplication on concrete\u003c\/h3\u003e\n\u003cp\u003eA different system build-up applies when used on concrete:\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eFirst treat absorbent concrete with UZIN PE 360 PLUS.\u003c\/li\u003e\n\u003cli\u003eThen apply one undiluted coat of UZIN PE 400.\u003c\/li\u003e\n\u003cli\u003eFor this application, the maximum residual moisture content is 3.5 CM-%.\u003c\/li\u003e\n\u003cli\u003eLevel the floor after it has dried completely.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eFor concrete, always have it checked whether this system build-up is suitable for the specific situation.\u003c\/p\u003e\n\u003ch3\u003eSubstrate preparation\u003c\/h3\u003e\n\u003cp\u003eThe substrate must be load-bearing, dimensionally stable, clean, sufficiently open, and free of cracks and substances that could reduce adhesion.\u003c\/p\u003e\n\u003cp\u003eRemove oil, grease, dust, laitance, and weak or loose layers. Poorly bonded adhesive, smoothing-compound, and floor-covering residues must be removed by sanding, milling, brushing, or dust-free abrasive blasting.\u003c\/p\u003e\n\u003cp\u003eCarefully sand mineral substrates and vacuum them thoroughly. Dense concrete surfaces, such as power-troweled or so-called blue concrete, may need to be shot-blasted.\u003c\/p\u003e\n\u003cp\u003eWhen used as a moisture barrier:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe substrate must be dry on the surface\u003c\/li\u003e\n\u003cli\u003eThere must be no standing water\u003c\/li\u003e\n\u003cli\u003eThe surface must be sufficiently absorbent and open\u003c\/li\u003e\n\u003cli\u003eThe moisture content must be determined beforehand using the correct measurement method\u003c\/li\u003e\n\u003cli\u003eA suitable sand-cement screed may contain a maximum of 4 CM-% residual moisture\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eApplication as a two-coat moisture barrier\u003c\/h3\u003e\n\u003cp\u003eStir UZIN PE 400 thoroughly before use. Use a rectangular application bucket and a fine-foam roller.\u003c\/p\u003e\n\u003ch4\u003eFirst coat\u003c\/h4\u003e\n\u003col\u003e\n\u003cli\u003eMix UZIN PE 400 with clean water in a 1:1 ratio.\u003c\/li\u003e\n\u003cli\u003eApply the mixture thinly, evenly, and with complete coverage.\u003c\/li\u003e\n\u003cli\u003eAvoid thick layers and puddle formation.\u003c\/li\u003e\n\u003cli\u003eAllow the first coat to dry for approximately one hour under normal conditions.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003ch4\u003eSecond coat\u003c\/h4\u003e\n\u003col\u003e\n\u003cli\u003eApply UZIN PE 400 undiluted.\u003c\/li\u003e\n\u003cli\u003eSpread the product thinly and evenly with a fine-foam roller.\u003c\/li\u003e\n\u003cli\u003eAvoid bare spots, thick coats and pooling.\u003c\/li\u003e\n\u003cli\u003eAllow the second coat to dry for approximately two hours.\u003c\/li\u003e\n\u003cli\u003eThen apply a suitable UZIN levelling compound.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003eDo not pour the product directly onto the floor. Clean tools immediately after use with water.\u003c\/p\u003e\n\u003ch3\u003eConsumption and drying time\u003c\/h3\u003e\n\u003cdiv class=\"group TyagGW_tableContainer\"\u003e\n\u003cdiv class=\"TyagGW_tableWrapper flex flex-col-reverse w-fit\" tabindex=\"-1\"\u003e\n\u003ctable class=\"w-fit min-w-(--thread-content-width)\"\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth class=\"last:pe-10\"\u003eCoat\u003c\/th\u003e\n\u003cth class=\"last:pe-10\"\u003eMixing ratio\u003c\/th\u003e\n\u003cth class=\"last:pe-10\"\u003eConsumption of PE 400\u003c\/th\u003e\n\u003cth class=\"last:pe-10\"\u003eDrying time\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eFirst coat\u003c\/td\u003e\n\u003ctd\u003eDiluted 1:1 with water\u003c\/td\u003e\n\u003ctd\u003eapprox. 50–75 g\/m²\u003c\/td\u003e\n\u003ctd\u003eapprox. 1 hour\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSecond coat\u003c\/td\u003e\n\u003ctd\u003eUndiluted\u003c\/td\u003e\n\u003ctd\u003eapprox. 100–125 g\/m²\u003c\/td\u003e\n\u003ctd\u003eapprox. 2 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTotal moisture barrier\u003c\/td\u003e\n\u003ctd\u003eTwo coats\u003c\/td\u003e\n\u003ctd\u003eapprox. 150–200 g\/m²\u003c\/td\u003e\n\u003ctd\u003eapprox. 3 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cp\u003eThe drying times apply at approximately 20 °C and 65% relative humidity. Low temperatures, high humidity and excessively thick coats slow down drying.\u003c\/p\u003e\n\u003ch3\u003eCoverage per canister\u003c\/h3\u003e\n\u003cp\u003eWhen used as a complete two-coat moisture barrier:\u003c\/p\u003e\n\u003cdiv class=\"group TyagGW_tableContainer\"\u003e\n\u003cdiv class=\"TyagGW_tableWrapper flex flex-col-reverse w-fit\" tabindex=\"-1\"\u003e\n\u003ctable class=\"w-fit min-w-(--thread-content-width)\"\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth class=\"last:pe-10\"\u003eTotal consumption\u003c\/th\u003e\n\u003cth class=\"last:pe-10\"\u003eCoverage per 12 kg canister\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e150 g\/m²\u003c\/td\u003e\n\u003ctd\u003eapprox. 80 m²\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e175 g\/m²\u003c\/td\u003e\n\u003ctd\u003eapprox. 69 m²\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e200 g\/m²\u003c\/td\u003e\n\u003ctd\u003eapprox. 60 m²\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cp\u003eThe amount of water required for the first coat is not included in this product consumption.\u003c\/p\u003e\n\u003ch3\u003eTechnical data\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eProduct type: dispersion moisture barrier\u003c\/li\u003e\n\u003cli\u003ePackaging: canister\u003c\/li\u003e\n\u003cli\u003eContents: 12 kg\u003c\/li\u003e\n\u003cli\u003eColour during application: white\u003c\/li\u003e\n\u003cli\u003eColour after drying: transparent\u003c\/li\u003e\n\u003cli\u003eUndiluted consumption: approx. 100–125 g\/m²\u003c\/li\u003e\n\u003cli\u003eConsumption for first diluted coat: approx. 50–75 g\/m² of product\u003c\/li\u003e\n\u003cli\u003eTotal product consumption as a moisture barrier: approx. 150–200 g\/m²\u003c\/li\u003e\n\u003cli\u003eDrying time of diluted coat: approx. 1 hour\u003c\/li\u003e\n\u003cli\u003eDrying time of undiluted coat: approx. 2 hours\u003c\/li\u003e\n\u003cli\u003eMinimum floor temperature: 10 °C\u003c\/li\u003e\n\u003cli\u003eShelf life: at least 12 months\u003c\/li\u003e\n\u003cli\u003eApplication: indoors\u003c\/li\u003e\n\u003cli\u003eComposition: polymer dispersion, additives and water\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhy choose UZIN PE 400?\u003c\/h3\u003e\n\u003cp\u003eUZIN PE 400 offers a fast solution for cement-based floors with elevated residual moisture levels. The system is easy to apply with a roller and, under suitable conditions, can be levelled within approximately three hours.\u003c\/p\u003e\n\u003cp\u003eThe combination of fast drying, alkali resistance and high vapour density makes it a practical moisture barrier for suitable cement and sand-cement floors above ground level.\u003c\/p\u003e","brand":"Uzin","offers":[{"title":"Default Title","offer_id":63299484057930,"sku":null,"price":229.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0969\/2194\/4394\/files\/uzinpe400.jpg?v=1787636875","url":"https:\/\/portofaltea.es\/pl\/products\/uzin-pe-400-vochtscherm-12-kg","provider":"Port of Altea","version":"1.0","type":"link"}