{"product_id":"uzin-nc-567-fusiontec-zelfnivellerende-dunne-dekvloer-20-kg","title":"UZIN NC 567 FusionTec Self-Leveling Thin Screed – 20 kg","description":"\u003cp class=\"PDq2pG_selectionAnchorContainer\"\u003e\u003cstrong\u003eUZIN NC 567 FusionTec\u003c\/strong\u003e is a self-leveling, virtually stress-free thin screed for layer thicknesses of \u003cstrong\u003e3 to 50 mm\u003c\/strong\u003e. The product can be used as a bonded screed and as an unbonded screed on a separation layer.\u003cspan class=\"PDq2pG_selectionAnchor\"\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003eThanks to its good flow properties and long working time, UZIN NC 567 is suitable for large areas and application with pumping systems. The product forms a level, stable, and absorbent substrate for textile and resilient floor coverings, parquet, ceramic tiles, and natural stone.\u003c\/p\u003e\n\u003cp\u003eThe thin screed can also be used for embedding and filling hot-water and electric underfloor heating systems. UZIN NC 567 is also a system component of the \u003cstrong\u003eUZIN Turbolight System CA\u003c\/strong\u003e.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eKey properties\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eSelf-leveling FusionTec thin screed\u003c\/li\u003e\n\u003cli\u003eSuitable for layer thicknesses of 3 to 50 mm\u003c\/li\u003e\n\u003cli\u003eSuitable as a bonded screed\u003c\/li\u003e\n\u003cli\u003eSuitable as an unbonded screed on a separation layer\u003c\/li\u003e\n\u003cli\u003eVirtually stress-free curing\u003c\/li\u003e\n\u003cli\u003eGood absorbency\u003c\/li\u003e\n\u003cli\u003eHigh load-bearing capacity\u003c\/li\u003e\n\u003cli\u003eSuitable for large areas\u003c\/li\u003e\n\u003cli\u003eSuitable for manual application and pumping\u003c\/li\u003e\n\u003cli\u003eSuitable for embedding underfloor heating\u003c\/li\u003e\n\u003cli\u003eWorking time of approximately 30 to 40 minutes\u003c\/li\u003e\n\u003cli\u003eWalkable after approximately 8 hours\u003c\/li\u003e\n\u003cli\u003eSuitable for textile and resilient floor coverings\u003c\/li\u003e\n\u003cli\u003eSuitable for parquet, tiles, and natural stone\u003c\/li\u003e\n\u003cli\u003eFor indoor use\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eThe stated times apply at approximately 20 °C and 65% relative humidity. Temperature, humidity, substrate, and layer thickness have a significant influence on drying time.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eApplications\u003c\/h3\u003e\n\u003cp\u003eUZIN NC 567 FusionTec can be used for:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCreating a bonded thin screed\u003c\/li\u003e\n\u003cli\u003eCreating a screed on a separation layer\u003c\/li\u003e\n\u003cli\u003eCreating virtually stress-free floor surfaces\u003c\/li\u003e\n\u003cli\u003eBridging greater differences in height\u003c\/li\u003e\n\u003cli\u003eEmbedding hot-water underfloor heating systems\u003c\/li\u003e\n\u003cli\u003eEmbedding suitable electric underfloor heating systems\u003c\/li\u003e\n\u003cli\u003eFilling studded-panel and WARP underfloor heating systems\u003c\/li\u003e\n\u003cli\u003eLarge areas processed with a pump\u003c\/li\u003e\n\u003cli\u003eUse as part of the UZIN Turbolight System CA\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eWithin the UZIN Turbolight System CA, a maximum point load of 2 kN applies. Always refer to the current system documentation.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eSuitable substrates\u003c\/h3\u003e\n\u003cp\u003eUZIN NC 567 can be used, in combination with the appropriate preparation and system build-up, on, among other substrates:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCement screeds\u003c\/li\u003e\n\u003cli\u003eCalcium sulfate and anhydrite screeds\u003c\/li\u003e\n\u003cli\u003eConcrete\u003c\/li\u003e\n\u003cli\u003eMagnesite and wood magnesite\u003c\/li\u003e\n\u003cli\u003eScrewed-down chipboards of classes P4 through P7\u003c\/li\u003e\n\u003cli\u003eScrewed-down OSB boards of classes OSB 2 through OSB 4\u003c\/li\u003e\n\u003cli\u003eWooden floorboards\u003c\/li\u003e\n\u003cli\u003eExisting mastic asphalt floors\u003c\/li\u003e\n\u003cli\u003eSuitable underfloor heating systems\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eOver chipboard, OSB, wooden floorboards, and mastic asphalt, the maximum layer thickness is 10 mm unless UZIN recommends otherwise for the relevant system build-up.\u003c\/p\u003e\n\u003cp\u003eThe floor is suitable for normal loads in residential and commercial areas and for loads from swivel castors in accordance with DIN EN 12529.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eMinimum layer thicknesses\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eAs a bonded layer: minimum 3 mm\u003c\/li\u003e\n\u003cli\u003eOver a separating layer: minimum 25 mm\u003c\/li\u003e\n\u003cli\u003eOver a separating layer in combination with UZIN RR 201 renovation fleece: minimum 20 mm\u003c\/li\u003e\n\u003cli\u003eOver chipboard, OSB, wooden floorboards, and mastic asphalt: maximum 10 mm\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eFor floating or unbonded constructions, the complete floor assembly must be assessed technically in advance.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eSubstrate preparation\u003c\/h3\u003e\n\u003cp\u003eThe substrate must be load-bearing, stable, dry, and free of cracks, dust, dirt, oil, and grease.\u003c\/p\u003e\n\u003cp\u003eFor bonded applications, all poorly bonded or bond-inhibiting layers must be completely removed by brushing, sanding, milling, or dust-free shot blasting. Then vacuum the substrate thoroughly.\u003c\/p\u003e\n\u003cp\u003eInstall suitable UZIN edge insulation strips along walls, columns, pipes, and other vertical building elements. Depending on the type and condition of the substrate, use a suitable primer and allow it to dry completely.\u003c\/p\u003e\n\u003cp\u003eWhen applying over a separating layer, the load-bearing substrate must be clean and free of loose particles. Install the film or separating layer flat, without folds, and with sufficient overlap.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eMixing and application\u003c\/h3\u003e\n\u003cp\u003ePour \u003cstrong\u003e3.2 liters of clean, cold water\u003c\/strong\u003e into a clean mixing tub. Then gradually add the entire contents of the 20 kg bag.\u003c\/p\u003e\n\u003cp\u003eMix the material mechanically with a suitable basket mixer until a homogeneous, lump-free consistency is achieved. Then pour the material onto the substrate and spread it evenly with a smoothing trowel or a squeegee for large areas.\u003c\/p\u003e\n\u003cp\u003eUZIN NC 567 can also be pumped mechanically. If necessary, use a spiked roller to remove trapped air and improve flow.\u003c\/p\u003e\n\u003cp\u003ePreferably apply the required layer thickness in a single operation.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eConsumption\u003c\/h3\u003e\n\u003cp\u003eAverage consumption is approximately \u003cstrong\u003e1.8 kg per m² per millimetre of layer thickness\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cdiv class=\"group TyagGW_tableContainer\"\u003e\n\u003cdiv class=\"TyagGW_tableWrapper flex flex-col-reverse w-fit\" tabindex=\"-1\"\u003e\n\u003ctable class=\"w-fit min-w-(--thread-content-width)\"\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth class=\"last:pe-10\"\u003eLayer thickness\u003c\/th\u003e\n\u003cth class=\"last:pe-10\"\u003eConsumption\u003c\/th\u003e\n\u003cth class=\"last:pe-10\"\u003eArea per 20 kg bag\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e3 mm\u003c\/td\u003e\n\u003ctd\u003eapproximately 5.4 kg\/m²\u003c\/td\u003e\n\u003ctd\u003eapproximately 3.7 m²\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e5 mm\u003c\/td\u003e\n\u003ctd\u003eapproximately 9 kg\/m²\u003c\/td\u003e\n\u003ctd\u003eapproximately 2.2 m²\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e10 mm\u003c\/td\u003e\n\u003ctd\u003eapproximately 18 kg\/m²\u003c\/td\u003e\n\u003ctd\u003eapproximately 1.1 m²\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e25 mm\u003c\/td\u003e\n\u003ctd\u003eapproximately 45 kg\/m²\u003c\/td\u003e\n\u003ctd\u003eapproximately 0.44 m²\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e50 mm\u003c\/td\u003e\n\u003ctd\u003eapproximately 90 kg\/m²\u003c\/td\u003e\n\u003ctd\u003eapproximately 0.22 m²\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cp\u003eActual consumption depends on the layer thickness, the evenness of the substrate and the selected system build-up.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eDrying time\u003c\/h3\u003e\n\u003cdiv class=\"group TyagGW_tableContainer\"\u003e\n\u003cdiv class=\"TyagGW_tableWrapper flex flex-col-reverse w-fit\" tabindex=\"-1\"\u003e\n\u003ctable class=\"w-fit min-w-(--thread-content-width)\"\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth class=\"last:pe-10\"\u003eApplication\u003c\/th\u003e\n\u003cth class=\"last:pe-10\"\u003eIndicative drying time\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eWalkable\u003c\/td\u003e\n\u003ctd\u003eafter approximately 8 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTextile and resilient floor coverings at 3 mm\u003c\/td\u003e\n\u003ctd\u003eapproximately 24 hours\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eEvery additional 10 mm of layer thickness\u003c\/td\u003e\n\u003ctd\u003eallow for a considerably longer drying time, up to approximately 5 extra days\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003cp\u003eFor thicker layers, always check that the screed is sufficiently dry before installing moisture-sensitive floor coverings or parquet.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eTechnical data\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eProduct type:\u003c\/strong\u003e self-levelling FusionTec thin screed\u003cbr\u003e\u003cstrong\u003ePackaging:\u003c\/strong\u003e 20 kg paper bag\u003cbr\u003e\u003cstrong\u003eColour:\u003c\/strong\u003e beige\/grey\u003cbr\u003e\u003cstrong\u003eLayer thickness:\u003c\/strong\u003e 3 to 50 mm\u003cbr\u003e\u003cstrong\u003eWater quantity:\u003c\/strong\u003e 3.2 litres per bag\u003cbr\u003e\u003cstrong\u003eConsumption:\u003c\/strong\u003e approximately 1.8 kg\/m² per mm of layer thickness\u003cbr\u003e\u003cstrong\u003eWorking time:\u003c\/strong\u003e approximately 30 to 40 minutes\u003cbr\u003e\u003cstrong\u003eWalkable:\u003c\/strong\u003e after approximately 8 hours\u003cbr\u003e\u003cstrong\u003eMinimum floor temperature:\u003c\/strong\u003e 10 °C\u003cbr\u003e\u003cstrong\u003eFlow spread:\u003c\/strong\u003e approximately 140 mm, plus or minus 5 mm\u003cbr\u003e\u003cstrong\u003eThermal conductivity:\u003c\/strong\u003e 1.4 W\/mK\u003cbr\u003e\u003cstrong\u003eFire classification:\u003c\/strong\u003e A1fl\u003cbr\u003e\u003cstrong\u003eShelf life:\u003c\/strong\u003e at least 12 months\u003cbr\u003e\u003cstrong\u003eQuantity per pallet:\u003c\/strong\u003e 54 bags\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eWhy choose UZIN NC 567 FusionTec?\u003c\/h3\u003e\n\u003cp\u003eUZIN NC 567 is suitable for flooring projects requiring greater layer thicknesses, high load-bearing capacity or the embedding of underfloor heating. Its virtually tension-free curing makes the product suitable for both bonded and unbonded floor constructions.\u003c\/p\u003e\n\u003cp\u003eThanks to its pumpability, the thin screed can be efficiently applied over large surfaces. The product forms a stable and absorbent base for a wide range of floor coverings.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"Uzin","offers":[{"title":"Default Title","offer_id":63283868598602,"sku":null,"price":42.5,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0969\/2194\/4394\/files\/uzinnc567.jpg?v=1787603082","url":"https:\/\/portofaltea.es\/da\/products\/uzin-nc-567-fusiontec-zelfnivellerende-dunne-dekvloer-20-kg","provider":"Port of Altea","version":"1.0","type":"link"}